View CM1460-08DE_1226760.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

CM1460 PraetorianTM L-C LCD and Camera EMI Filter Array with ESD Protection
Features
* * * * * * Four, six and eight channels of EMI filtering with integrated ESD protection Pi-style EMI filters in a capacitor-resistor-capacitor (C-R-C) network 15kV ESD protection on each channel (IEC 61000-4-2 Level 4, contact discharge) 30kV ESD protection on each channel (HBM) Greater than 20dB attenuation (typical) at 1 GHz TDFN package with 0.50mm lead pitch: * 4-ch. = 8-lead TDFN * 6-ch. = 12-lead TDFN * 8-ch. = 16-lead TDFN Tiny TDFN package size: * 8-lead: 2.00mm 2.00mm * 12-lead: 3.00mm x 1.35mm * 16-lead: 4.00mm x 1.60mm Increased robustness against vertical impacts during manufacturing process Lead-free version available
Product Description
California Micro Devices' CM1460 is a family of pi-style EMI filter arrays with ESD protection, which integrates four, six and eight filters (C-L-C) in small form factor TDFN 0.50mm pitch packages. Each EMI filter channel of the CM1460 is implemented as a 3-pole L-C filter where the component values are 15pF-17nH-15pF. The CM1460's roll-off frequency at -6dB attenuation is 350MHz and can be used in applications where the data rates are as high as 140Mbps while providing greater than 30dB over the 800MHz to 2.7GHz frequency range. The parts include ESD diodes on every pin, which provide a very high level of protection for sensitive electronic components that may be subjected to electrostatic discharge (ESD). The ESD protection diodes connected to the filter ports are designed and characterized to safely dissipate ESD strikes of 15kV, beyond the maximum requirement of the IEC61000-42 international standard. Using the MIL-STD-883 (Method 3015) specification for Human Body Model (HBM) ESD, the pins are protected for contact discharges at greater than 30kV. This device is particularly well suited for wireless handsets, mobile LCD modules and PDAs because of its small package format and easy-to-use pin assignments. In particular, the CM1460 is ideal for EMI filtering and protecting data and control lines for the LCD display and camera interface in mobile handsets. The CM1460 is housed in space saving, low profile 8, 12 and 16-lead TDFN packages where the pitch is 0.50mm and is available in lead-free format.
*
* *
Applications
* * * * * * LCD and Camera data lines in mobile handsets I/O port protection for mobile handsets, notebook computers, PDAs etc. EMI filtering for data ports in cell phones, PDAs or notebook computers. Wireless handsets Handheld PCs/PDAs LCD and camera modules
Electrical Schematic
17nH FILTER+ESDn* 15pF 15pF FILTER+ESDn*
GND
* See Package/Pinout Diagram for expanded pin information.
(c) 2006 California Micro Devices Corp. All rights reserved. 02/23/06
1 of 4, 6 or 8 EMI/RFI Filter Channels with Integrated ESD Protection
490 N. McCarthy Blvd., Milpitas, CA 95035-5112
Tel: 408.263.3214
Fax: 408.263.7846
www.cmd.com
1
CM1460
PACKAGE / PINOUT DIAGRAMS
(Pins Down View) 8765
TOP VIEW
BOTTOM VIEW
(Pins Up View) 1234
(Pins Down View)
12 11 10 9 8 7
TOP VIEW
BOTTOM VIEW
(Pins Up View)
123456
Pin 1 Marking
YF/YE
GND
PAD
Pin 1 Marking
N61F/N61E
GND PAD
1234
8765
12345
6
12 11 10 9 8 7
CM1460-04DE 8 Lead TDFN Package TOP VIEW
(Pins Down View)
CM1460-06DE 12 Lead TDFN Package BOTTOM VIEW
(Pins Up View)
1234567 8
16 15 14 13 12 11 10 9
Pin 1 Marking
N618F/N618E
GND PAD
Notes: 1) These drawings are not to scale.
12345
67
8
16 15 14 13 12 11 10 9
CM1460-08DE 16 Lead TDFN Package
PIN DESCRIPTIONS
DEVICE PIN(s) -04 1 2 3 4 -06 1 2 3 4 5 6 -08 1 2 3 4 5 6 7 8 GND PAD NAME FILTER1 FILTER2 FILTER3 FILTER4 FILTER5 FILTER6 FILTER7 FILTER8 GND DESCRIPTION Filter + ESD Channel 1 Filter + ESD Channel 2 Filter + ESD Channel 3 Filter + ESD Channel 4 Filter + ESD Channel 5 Filter + ESD Channel 6 Filter + ESD Channel 7 Filter + ESD Channel 8 Device Ground DEVICE PIN(s) -04 8 7 6 5 -06 12 11 10 9 8 7 -08 16 15 14 13 12 11 10 9 NAME FILTER1 FILTER2 FILTER3 FILTER4 FILTER5 FILTER6 FILTER7 FILTER8 DESCRIPTION Filter + ESD Channel 1 Filter + ESD Channel 2 Filter + ESD Channel 3 Filter + ESD Channel 4 Filter + ESD Channel 5 Filter + ESD Channel 6 Filter + ESD Channel 7 Filter + ESD Channel 8
Ordering Information
PART NUMBERING INFORMATION
Lead-free Finish Pins 8 12 16 Package TDFN-8 TDFN-12 TDFN-16 Ordering Part Number1 CM1460-04DE CM1460-06DE CM1460-08DE Part Marking YE N61E N618E
Note 1: Parts are shipped in Tape & Reel form unless otherwise specified.
(c) 2006 California Micro Devices Corp. All rights reserved.
2
490 N. McCarthy Blvd., Milpitas, CA 95035-5112
Tel: 408.263.3214
Fax: 408.263.7846
www.cmd.com
02/23/06
CM1460
Specifications
ABSOLUTE MAXIMUM RATINGS
PARAMETER Storage Temperature Range Current per Inductor DC Package Power Rating RATING -65 to +150 30 500 UNITS C mA mW
STANDARD OPERATING CONDITIONS
PARAMETER Operating Temperature Range RATING -40 to +85 UNITS C
ELECTRICAL OPERATING CHARACTERISTICS (SEE NOTE1)
SYMBOL L CTOTAL C VDIODE ILEAK VSIG PARAMETER Channel Inductance Total Channel Capacitance Capacitance C1 Standoff Voltage Diode Leakage Current (reverse bias) Signal Clamp Voltage Positive Clamp Negative Clamp In-system ESD Withstand Voltage a) Human Body Model, MIL-STD-883, Method 3015 b) Contact Discharge per IEC 61000-4-2 Level 4 Dynamic Resistance Positive Negative Roll-off Frequency at 06dB Attenuation ZSOURCE=50, ZLOAD=50 At 2.5VDC Reverse Bias, 1MHz, 30mVAC At 2.5VDC Reverse Bias, 1MHz, 30mVAC IDIODE=10A VDIODE=+3.3V ILOAD = 10mA ILOAD = -10mA Notes 2, 3and 4 30 15 2.3 0.9 350 kV kV MHz 5.6 -1.5 24 12 CONDITIONS MIN TYP 17 30 15 6.0 0.1 6.8 -0.8 1.0 9.0 -0.4 36 18 MAX UNITS nH pF pF V A V V
VESD
RDYN
fC
Note 1: TA=25C unless otherwise specified. Note 2: ESD applied to input and output pins with respect to GND, one at a time. Note 3: Clamping voltage is measured at the opposite side of the EMI filter to the ESD pin (i.e. if ESD is applied to pin A1 then clamping voltage is measured at pin C1). Unused pins are left open. Note 4: These parameters are guaranteed by design and characterization.
(c) 2006 California Micro Devices Corp. All rights reserved. 02/23/06
490 N. McCarthy Blvd., Milpitas, CA 95035-5112
Tel: 408.263.3214
Fax: 408.263.7846
www.cmd.com
3
CM1460
Performance Information
Typical Filter Performance (TA=25C, DC Bias=0V, 50 Ohm Environment)
Figure 1. Typical EMI Filter Performance Typical Diode Capacitance vs. Input Voltage
Capacitance (Normalized)
DC Voltage
Figure 2. Filter Capacitance vs. Input Voltage (normalized to capacitance at 2.5VDC and 25C)
(c) 2006 California Micro Devices Corp. All rights reserved.
4
490 N. McCarthy Blvd., Milpitas, CA 95035-5112
Tel: 408.263.3214
Fax: 408.263.7846
www.cmd.com
02/23/06
CM1460
Mechanical Details
TDFN-08 Mechanical Specifications The CM1460-04DE is supplied in an 8-lead, 0.5mm pitch TDFN package. Dimensions are presented below. For complete information on the TDFN-08, see the California Micro Devices TDFN Package Information document. Mechanical Package Diagrams
D
8765
PACKAGE DIMENSIONS
Package JEDEC No. Leads Dim. A A1 A2 A3 b D D2 E E2 e K L L2 R r1 # per tube # per tape and reel 0.075 0.075 NA 3000 pieces
K e
TDFN MO-229 (Var. VCCD-3) 8 Millimeters Min 0.70 0.00 0.55 0.20 1.50 0.80 0.20 0.20 0.30 0.40 0.13 0.003 0.003 Nom 0.75 0.02 0.65 0.20 0.25 2.00 1.60 2.00 0.90 0.50 0.008 0.008 0.012 0.016 0.005 1.00 0.031 1.70 0.059 0.30 0.008 Max 0.80 0.05 0.80 Min 0.028 0.000 0.022 Inches Nom 0.030 0.001 0.026 0.008 0.010 0.079 0.063 0.079 0.035 0.020 0.039 0.067 0.012 Max 0.031 0.002 0.031
E
Pin 1 Marking
1234 TOP VIEW
0.10 C
0.08 C
A1
SIDE VIEW
A
A3 A2
1234
D2 r1
GND PAD
E2
C0.25 R L
8765
b
8X
Controlling dimension: millimeters
BOTTOM VIEW
0.10
M
CAB
This package is compliant with JEDEC standard MO-229, variation VCCD-3 with exception of the "D2" and "E2" dimensions as called out in the table above and the "r1" dimension which is not specified in the MO-229 standard.
Package Dimensions for 8-Lead, 0.5mm pitch TDFN Package
(c) 2006 California Micro Devices Corp. All rights reserved. 02/23/06
490 N. McCarthy Blvd., Milpitas, CA 95035-5112
Tel: 408.263.3214
Fax: 408.263.7846
www.cmd.com
5
CM1460
Mechanical Details (cont'd)
TDFN-12 Mechanical Specifications The CM1460-06DE is supplied in an 12-lead, 0.5mm pitch TDFN package. Dimensions are presented below. For complete information on the TDFN-12, see the California Micro Devices TDFN Package Information document.
E
Mechanical Package Diagrams
D
12 11 10 9 8 7
Pin 1 Marking
PACKAGE DIMENSIONS
Package JEDEC No. Leads Dim. A A1 A3 b D D2 E E2 e K L # per tape and reel 0.20 0.20 0.25 0.30 0.20 2.90 2.40 1.25 0.30 Millimeters Min 0.70 0.00 Nom 0.75 0.02 0.20 REF 0.25 3.00 2.50 1.35 0.40 0.50 BSC 0.008 0.008 0.010 0.012 3000 pieces 0.30 3.10 2.60 1.45 0.50 Max 0.80 0.05 Min 0.028 0.000 0.008 0.114 0.095 0.049 0.012 TDFN MO-229C 12 Inches Nom 0.030 0.001 0.010 0.118 0.098 0.053 0.016 Max 0.031 0.002 0.012 0.122 0.102 0.057 0.020
Pin 1 Locator
e
0.08 C 0.10 C
123456 TOP VIEW
0.008 REF
A1
SIDE VIEW
A
A3
8X 0.10
M
CAB
b
1
2
C0.2
3
4
5
6
E2
0.020 BSC
K
GND PAD
9
D2 L
12 11 10
8
7
BOTTOM VIEW
Controlling dimension: millimeters
This package is compliant with JEDEC standard MO-229C with the exception of the "D", "D2", "E", "E2", "K" and "L" dimensions as called out in the table above.
Dimensions for 12-Lead, 0.5mm pitch TDFN package
(c) 2006 California Micro Devices Corp. All rights reserved.
6
490 N. McCarthy Blvd., Milpitas, CA 95035-5112
Tel: 408.263.3214
Fax: 408.263.7846
www.cmd.com
02/23/06
CM1460
Mechanical Details (cont'd)
TDFN-16 Mechanical Specifications The CM1460-08DE is supplied in an 16-lead, 0.5mm pitch TDFN package. Dimensions are presented below. For complete information on the TDFN-16, see the California Micro Devices TDFN Package Information document.
E
Mechanical Package Diagrams
D
16 15 14 13 12 11 10 9
Pin 1 Marking
PACKAGE DIMENSIONS
Package JEDEC No. Leads Dim. A A1 A3 b D D2 E E2 e K L # per tape and reel 0.20 0.20 0.30 0.40 3.90 3.10 1.50 0.30 Millimeters Min 0.70 0.00 0.40 Nom 0.75 0.02 0.55 0.20 REF 4.00 3.20 1.60 0.40 0.50 BSC 0.008 0.008 0.010 0.012 3000 pieces 4.10 3.30 1.70 0.50 Max 0.80 0.05 0.70 Min 0.028 0.000 0.016 0.153 0.122 0.059 0.012 TDFN MO-229C 16 Inches Nom 0.030 0.001 0.022 0.157 0.126 0.063 0.016 BSC
K
0.10 C
12345678 TOP VIEW
Max 0.031 0.002 0.028 0.161 0.130 0.067 0.020
Pin 1 Locator
e
0.08 C
A1
SIDE VIEW
A
A3
0.008 REF
8X 0.10
M
CAB
b
1
2
3
C0.2
4
5
6
7
8
E2
GND PAD
9
16 15 14 13 12 11 10
D2
L
BOTTOM VIEW
Controlling dimension: millimeters
This package is compliant with JEDEC standard MO-229C with the exception of the "D", "D2", "E", "E2", "K" and "L" dimensions as called out in the table above.
Dimensions for 16-Lead, 0.5mm pitch TDFN package
(c) 2006 California Micro Devices Corp. All rights reserved. 02/23/06
490 N. McCarthy Blvd., Milpitas, CA 95035-5112
Tel: 408.263.3214
Fax: 408.263.7846
www.cmd.com
7

▲Up To Search▲

Price & Availability of CM1460-08DE

	To Download CM1460-08DE Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .